UF3-2100 : 1 GS/s 8 bit Waveform Digitizer
- Up to 1 GS/s on one channel or 500 MS/s on two channels
- Simultaneous sampling on all channels
- Separate monolithic ADC and amplifier per channel
- 8 input ranges: ±50 mV up to ±10 V
- Up to 2 synchronous digital channels with multi-purpose I/O
- 512 MSample signal memory, up to 4 GSample
- Window, re-arm, OR/AND triggers
- Synchronization of up to 8 cards per system
- Windows, Linux, MATLAB, LabVIEW drivers included
- Multiple Recording, ABA Mode and Time Stamp included
- Two years hardware warranty
- Life time free technical support and software updates
UF3-2100 Series Overview
There are 4 different 8-bit waveform digitizer cards in the UF3-2100 range. Cards are available offering 1 or 2 input channels and choice of 1 GS/s or 500 MS/s maximum A/D sampling rates.Applications
Typical applications include ATE, RADAR, Lidar, communications.
|Maximum sampling rates|
|P/N||1 channel||2 channels|
|UF3-2122||500 MS/s||250 MS/s|
|UF3-2132||1 GS/s||500 MS/s|
Note: 1Sample=1 BytesNew Features and Compared to UF2 Series
The UF3 series is the latest generation of digitizer cards from Strategic Test. The UF3 is based on a totally new carrier board design - our 5th generation - that now includes the following updated or new features::
- Higher transfer rates from ADC's to onboard memory. This was essential to enable recording at faster sample rates with high ADC resolutions.
- Additional connections. Five multi-purpose are routed to clock input, clock output, trigger input, trigger output and 2 freely programmable I/O connections. These can be used as :
- fast digital inputs that are synchronous with the analog channels
- asynchronous digital i/o for reading or writing status information
- extra tigger input or output lines. Inputs can be AND, OR with the external input signal
There are two input paths per channel on the card. One path is a fixed 50 Ohm path, while the other path is buffered can be configured with either 50 Ohm or 1 M Ohm termination. Both paths have 8 input ranges (+-50 mV ... +-10 V). The new frontend module now allows AC or DC coupling, and includes a user activated low pass filter.Standard mode...
The signals can be recorded to the onboard signal memory at the maximum clock rate using Standard mode. At the end of the measurement, the data is off-loaded to the PC using DMA at the maximum PCI Express bus data transfer rate of up to 245 MBytes/s. While recording, the card operates independently of the host PC which is available for other tasks.... and FIFO mode. Record continuously at 245 MBytes per second to PC
Alternatively, the UF3 boards also provide a FIFO mode that continuously transfers recorded data gap-free to the PC during the measurement at up to 245 MBytes/s. This mode has the advantage that more samples can be recorded than the available on-board memory.
Note that the maximum sampling rate is limited by the 66 MHz PCI bus transfer rate, which is typically 245 MBytes/s, and the number of activated channels. For 8-bit A/D boards this equates to a max sampling rate of f=245M/n where n is the total number of activated channels (including all cards in the system).Synchronizing multiple-cards in a single PC
The Star Hub option is an add-on that allows multiple cards, even of different types, to be synchronized.
The Star Hub distributes the clock and trigger signals, so all channels are without time-skew errors and all cards start on the same trigger condition (any channel, any external TTL trigger). Any card can be defined as the clock master or trigger master by software. It's also possible to configure AND/OR trigger conditions (channel or external TTL) across multiple cards.
Please note that the UF3 verion of the Star Hub is not compatible with the UF2 or UF Star Hub options.Independent amplifers to match each channel to the sensor
Each channel has it's own amplifier and dcV offset adjustment. This means you are able to selecta suitbale voltage range and adjust the dcV offset to best match the output from your sensor, for every channel.Fine Resolution Sampling Rates
Most other products limit you to a few fixed sampling rate choices, however with the UF3 cards you simply instruct the software which rate you require and the driver will automatically adjust the onboard PLL and hardware divider to achieve the closest sampling rate possible.External Clock and External Trigger
Need to synchronize with external equipment? As standard the UF3 cards are supplied with connectors for external clock and trigger. Both can be programmed as input or output, so the card can receive a TTL clock or output the internal clock and the trigger connector can receive a TTL trigger event or generate a trigger event from either a software trigger or detected channel trigger.Flexible Triggering
The UF3 cards offer an exceptional range of trigger possibilities to avoid false triggering:
- Edge and Level: positive, negative, both edges
- Window: define high/low levels; entry, exit
- Re-Arm : define a level that has to be crossed first, avoids triggering on noise
- Pulse-width: define a time period, trigger must occur inside/outside to be true
- External TTL: edge, can be used in combination with pulse-width
- Double edge: can be used with channel or external triggers
- AND/OR trigger masks: can be used with channel/ external and digital inputs
- Force trigger: used to start card if trigger not detected after given time
- Delay trigger: can delay AND/OR masks by up to 64 ksamples
Only six key functions to define a complete setup. Small DLL or module (Linux) uses few system resources and does not conflict with other programs. On request, we will be pleased to send you the User Manual as a pdf so you can see the many examples.
The API is identical for all UF3 and UF2 A/D D/A and Digital cards to reduce programming times.What's included
The UF3 cards are supplied with:
- Windows (8, 7, Vista, XP, XP64, 2000) and Linux drivers (RedHat, Fedora, SuSe, SARGE)
- Extensive printed user manual with many programming examples
- Source code programming examples: C/C++, LabVIEW (Windows), MATLAB (Windows and Linux), LabWindows/CVI, IVI, .NET, Delphi, Visual Basic, Python
- SBench 6 Base version for Windows and Linux
- Two years hardware warranty
- Lifetime software updates (inc. future OS versions)
- Lifetime technical support from specialists