Customers
UF2e-2020
Resources
Datasheet, pdf

UF3e-4800 Waveform Digitizers / Transient Recorders
16-bit up to 180MS/s, 1 or 2 channels
PCI Express cards

  • Up to 180 MS/s on one channel or two channels
  • Simultaneous sampling on all channels
  • Separate monolithic ADC and amplifier per channel
  • 6 input ranges: ±200 mV up to ±10 V
  • Up to 2 synchronous digital channels with multi-purpose I/O
  • 512 MByte onboard memory
  • Multiple Recording, Gated Sampling, ABA Mode and Time Stamp
  • Drivers for LabVIEW, MATLAB and LabWindows
  • Windows and Linux drivers included.
  • Two years hardware warranty

 

UF3-4800 Series Overview

There are 6 different 16-bit waveform digitizer cards in the UF3e-4800 range. Cards are available offering 1 or 2 input channels and choice of 65 MS/s, 105 MS/s or 180 MS/s maximum A/D sampling rates

Applications

Typical applications include ATE, research, communications.

  Maximum sampling rates
P/N 1 channel 2 channels
UF3e-4830 65 MS/s -
UF3e-4831 65 MS/s 65 MS/s
UF3e-4840 105 MS/s -
UF3e-4841 105 MS/s 105 MS/s
UF3e-4860 180 MS/s -
UF3e-4861 180 MS/s 180 MS/s

Note: 1Sample=2Bytes

New Features and Compared to UF2 Series

The UF3 series is the latest generation of digitizer cards from Strategic Test. The UF3 is based on a totally new carrier board design - our 5th generation - that now includes the following updated or new features::

  • Higher transfer rates from ADC's to onboard memory. This was essential to enable recording at faster sample rates with high ADC resolutions.
  • Additional connections. Five multi-purpose are routed to clock input, clock output, trigger input, trigger output and 2 freely programmable I/O connections. These can be used as :
    • fast digital inputs that are synchronous with the analog channels
    • asynchronous digital i/o for reading or writing status information
    • extra tigger input or output lines. Inputs can be AND, OR with the external input signal
New ADC Module Features

There are two input paths per channel on the card. One path with 6 input ranges (+-200 mV ... +-10 V) and the ability to use 1 MOhm input impedance and one path that delivers a bandwidth of 250 MHz but has 4 input ranges (+-500 mV ... +-5 V).

The new frontend module now allows AC or DC coupling, and includes a user activated low pass filter. As with the UF2 ADC module each channel can be independently configured with 50 Ohm or 1 MOhm impedance, and have it's own voltage range.

Standard mode...

The signals can be recorded to the onboard signal memory at the maximum clock rate using Standard mode. At the end of the measurement, the data is off-loaded to the PC using DMA at the maximum PCI Express bus data transfer rate of up to 160 MBytes/s. While recording, the card operates independently of the host PC which is available for other tasks.

... and FIFO mode. Record continuously at up to 160 MBytes per second to PC

Alternatively, the UF3e boards also provide a FIFO mode that continuously transfers recorded data gap-free to the PC during the measurement at up to 160 MBytes/s. This mode has the advantage that more samples can be recorded than the available on-board memory.

Note that the maximum sampling rate is limited by the PCI Express bus transfer rate, which is typically 160 MBytes/s, and the number of activated channels. For 16/14/12-bit A/D boards this equates to a max sampling rate of f=160M/2/n where n is the total number of activated channels (including all cards in the system).

Synchronizing multiple-cards in a single PC

The Star Hub option is an add-on that allows multiple cards, even of different types, to be synchronized. 

The Star Hub distributes the clock and trigger signals, so all channels are without time-skew errors and all cards start on the same trigger condition (any channel, any external TTL trigger). Any card can be defined as the clock master or trigger master by software. It's also possible to configure AND/OR trigger conditions (channel or external TTL) across multiple cards.

Please note that the UF3 version of the Star Hub is not compatible with the UF2 or UF Star Hub options.

Independent amplifers to match each channel to the sensor

Each channel has it's own amplifier and dcV offset adjustment. This means you are able to selecta suitbale voltage range and adjust the dcV offset to best match the output from your sensor, for every channel.

Fine Resolution Sampling Rates

Most other products limit you to a few fixed sampling rate choices, however with the UF3e cards you simply instruct the software which rate you require and the driver will automatically adjust the onboard PLL and hardware divider to achieve the closest sampling rate possible.

External Clock and External Trigger

Need to synchronize with external equipment? As standard the UF3e cards are supplied with connectors for external clock and trigger. Both can be programmed as input or output, so the card can receive a TTL clock or output the internal clock and the trigger connector can receive a TTL trigger event or generate a trigger event from either a software trigger or detected channel trigger.

Flexible Triggering

The UF3e cards offer an exceptional range of trigger possibilities to avoid false triggering:

  • Edge and Level: positive, negative, both edges
  • Window: define high/low levels; entry, exit
  • Re-Arm : define a level that has to be crossed first, avoids triggering on noise
  • Pulse-width: define a time period, trigger must occur inside/outside to be true
  • External TTL: edge, can be used in combination with pulse-width
  • Double edge: can be used with channel or external triggers
  • AND/OR trigger masks: can be used with channel/ external and digital inputs
  • Force trigger: used to start card if trigger not detected after given time
  • Delay trigger: can delay AND/OR masks by up to 64 ksamples
Easy Programming

Only six key functions to define a complete setup. Small DLL or module (Linux) uses few system resources and does not conflict with other programs. On request, we will be pleased to send you the User Manual as a pdf so you can see the many examples.

The API is identical for all UF3 and UF2 A/D D/A and Digital cards to reduce programming times.

What's included

The UF3 cards are supplied with:

  • Windows (8, 7, Vista, XP, XP64, 2000) and Linux drivers (RedHat, Fedora, SuSe, SARGE)
  • Extensive printed user manual with many programming examples
  • Source code programming examples: C/C++, LabVIEW (Windows), MATLAB (Windows and Linux), LabWindows/CVI, IVI, .NET, Delphi, Visual Basic, Python
  • SBench 6 Base version for Windows and Linux
  • Two years hardware warranty
  • Lifetime software updates (inc. future OS versions)
  • Lifetime technical support from specialists
Features
Standard Features
Onboard signal memory
512 MBytes standard. Expandable to 2 GBytes onboard.
Standard mode
Record at max rates of A/D's into card memory
FIFO mode
Up to 160 MBytes/s data streaming to PC memory
External clock I/O
Clock input/output for synchronization with external systems
External trigger I/O
Trigger input/output for synchronization with external systems
Reference clock
Input of high precision external reference clock
Fast Digital Inputs
Synchronous with analog inputs
Asynch Digital I/O
To read/write status signals
Ext trigger I/O
Additional trigger lines can be AND, OR with Ext Trigger
Memory segmentation and auto re-arm trigger for recording high-speed series of waveforms at high repetition rates. Especially suited to capture RADAR pulses.
Records the time of trigger events in an extra FIFO buffer
ABA Mode
Dual timebase for continuus fast/slow sampling based on trigger events
Optional Features
Memory upgrades
512, 1024, 2048 MSamples
Asynch digital I/O's for control, read status or trigger off external equipment
Perfect synchronization of up to 8 boards.